Anchor Frame Collar 1.6m For L44A1 Mast

  • Anchor Frame Collar 1.6m For L44A1 Mast
  • Anchor Frame Collar 1.6m For L44A1 Mast
  • Anchor Frame Collar 1.6m For L44A1 Mast
Anchor Frame Collar 1.6m For L44A1 Mast
  • ZCJJ
  • China
  • 5 to 30days
  • 50 to 200 pcs, sets

Oman Tower Crane, Yemen Tower Crane

Products Specification

Type , Model: Anchor Frame Collar 1.6m For L44A1 Mast

Size: 1.6m for 1.6M L type mast

Materials: Q345B

Process: Blasting derusting, 

Painting:  Under painting , Middle painting, Surface painting.

Our factory produce and supply almost all famous brand tower crane :Mast section, Anchor Frame, Fixing angle ,Adaptor and so on as good quality and price.

Anchor Frame L44A1

Collar 1.6m L44A1 Mast

MC

Anchor Frame Collar 1.6m For L44A1 Mast

Tower Crane Knowledge sharing:

Maintenance of the tower crane turning support

This paper describes the maintenance and maintenance of tower crane accessories - tower crane swing bearing installation, which is divided into nine points

(1) the mounting support of the slewing bearing (the seat on the lower surface of the supporting ring and the seat on the upper surface of the inner ring) must be rigid enough, and the mounting surface must be smooth. Before the slewing support is assembled, the bearing should be de-stressed to reduce the deformation of the slewing support.

The contact surface between the support and the slewing support must be cleaned during assembly.

Anchor Frame Collar 1.6m For L44A1 Mast

(2) pay attention to the change of noise and the change of rotary resistance moment in use, and disassemble and inspect if there is any abnormal phenomenon.

(3) the slewing support must be hoisted or stored horizontally, but not vertically to avoid deformation.

(4) before the bolt is completely tightened, the meshing inspection of the gear shall be carried out, and the meshing condition shall meet the requirements of gear accuracy: that is, the contact spots distributed on the tooth surface of the gear pair after running under slight braking shall be no less than 25% in the direction of the tooth height and no less than 30% in the direction of the tooth length.

Anchor Frame Collar 1.6m For L44A1 Mast

(5) for 10 shifts of tooth surface work, debris shall be removed once and grease shall be re-applied.

(6) in order to ensure the reliability of bolt work and avoid the insufficient pre-tightening force of bolts, the pre-tightening torque of bolts should be checked respectively after the first 100 hours and 500 hours of rotary support work. After that, the pre-tightening torque should be checked every 1000 hours.

(7) high strength bolts and nuts are used to connect the slewing support; Use double nuts to tighten and prevent loose.

Anchor Frame Collar 1.6m For L44A1 Mast

(8) when tightening the nut, lubricate the thread of the bolt and the end face of the nut, and tighten it symmetrically and evenly in the circumferential direction many times with the torque wrench. When tightening for the last time, the pre-tightening torque on each bolt should be roughly uniform.

(9) four oil cups are arranged on the upper surface of the gear ring of the slewing support and aligned with the raceway, so as to add grease to the raceway. In general, the slewing bearing is lubricated once every 50 hours. Add enough oil each time until the oil oozes from the seal.

Anchor Frame Collar 1.6m For L44A1 Mast

 

Get the latest price? We'll respond as soon as possible(within 12 hours)

Privacy policy

close left right